2021年我公司鋼筋成型彎箍機在原有的過硬基礎上升級，利用氣缸壓緊，空氣壓縮機動力，更換鋼筋加工直徑不用更換其他，一鍵操作可設置。

自動鋼筋彎箍機HH4-12S二號機型，采用雙同步帶設置，大功率，針對加工4-12mm圓鋼和螺紋，可將對角箍筋1.3米內的套子一機成型，同時支持定制加工加筋。

雙線箍筋機，公司自動數控鋼筋彎箍機采用氣動原理，進料機構結合設備，可單線，雙線調直彎箍切斷。同時公司還有“曲線型調直鋼筋彎箍機”，針對加工4-13mm鋼筋。

鋼筋成型彎箍機參數:

支持加工異形箍筋，正反彎箍

支持小尺寸的加筋加工

箍筋尺寸小6公分

箍筋尺寸大130公分

數控系統采用PLC，可觸摸操作。

產品針對地域均可發貨

1.1.6 Good grounding

In order to ensure the normal operation of the control system, improve system reliability, and ensure the personal safety of the operator, all parts of the control system should be well grounded.

The ground wire of the system should ensure that the wire diameter is not less than 4 square millimeters, and the distance to the ground terminal should be shortened as much as possible.

The ground terminal (negative terminal) of DC 24V must be disconnected from the ground.

1.1.7 System protection

Keep the control system isolated from the external environment to prevent dust, dust, metal dust and other debris from entering the control system, which may cause the control system to work abnormally, damage system components, and reduce system life.

The LCD screen (fragile) of the control system should be protected: keep it away from sharp objects; prevent objects in the air from hitting the screen; do not use your fingers to point, gesture, or tap on the screen; when the screen is dusty and needs to be cleaned, ·Use a soft paper towel or cotton cloth to wipe gently.

1.1.6 良好接地

為了讓控制系統正常工作、提高系統可靠性、操作者人身安全，控制系統的所有部 分均應良好接地。系統的地線應線徑不小于 4 平方毫米，且盡量縮短與入地端的距離。

直流 24V 的地端（負端）需與大地斷開。

1.1.7 系統的防護

保持控制系統與外部環境的隔離，以避免由于灰塵、粉塵、金屬粉塵等雜物進入控制系統 內部而造成控制系統工作不正常、系統部件損壞、降低系統壽命等。

應防護好控制系統的液晶屏幕（易碎品）：使其遠離尖銳物體；避免空中的物體撞到屏幕上 ; 不能用手指在屏幕上指點、比劃、敲打；當屏幕有灰塵需要清潔時，應·用柔軟的紙巾或棉布輕 輕擦除。